Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bronx1

Pages: [1] 2 3
1
Tech Clinic / problems with win2k and Asus A7N8X-Dlx, AMD 2800+
« on: January 20, 2004, 05:14:23 PM »
Have you checked you memory timings. Also if you have the motherboard monitor set to low temps this will also cause restarts. I have the Asus A7N8X-X.
I was OCing the memory that cause my ramdom restarts. Good luck

2
Tech Clinic / problems with bios flashing
« on: January 11, 2004, 07:27:07 PM »
Resetting may help. Itsure can't hurt, all you will have to do it reset all of your settings.

3
Tech Clinic / system conflict !!
« on: January 11, 2004, 10:29:23 AM »
What kind of card do you have. Try updating the driver for you MOBO and card. Also if it is pci. Try different slots. You may have to go into device manager and remove the NIC card first. Good luck.

4
Hardware / RAM Problem ?
« on: January 11, 2004, 10:25:53 AM »
Which MOBO do you have. Did you try placing the in slot 1,3. Sometimes you need to change slot config. Also try updating the bios.

5
Hardware / CDs in cd drive(s) not responding
« on: December 25, 2003, 10:59:43 AM »
I could be the firmware update caused problems with the Ide drivers. Try uninstalling your update. If that doesn't work try to clear the cmos and reset settings. Or try to reinstall your ide drivers.

6
Tech Clinic / Src:Line:6Error:0Scode:800401f3
« on: November 08, 2003, 05:20:36 PM »
Do a Google search for SmartIssue. You need to spor the program from starting when you start window.

7
Hardware / how reliable is AMD processor
« on: November 08, 2003, 05:16:40 PM »
I have always used AMD. Neverany problems overclocked not a problem. I have seen pentium4 burn up. Go with AMD.

8
Hardware / CD ROM Not displaying
« on: October 22, 2003, 03:25:41 PM »
Did you try add and remove hardware. It it on the same ide channel as the old cdrom.

9
Tech Clinic / cmos settings incorrect
« on: September 23, 2003, 09:16:23 PM »
If you do junk it . Remover the hard drive and beat it with a hammer. You do not want anyone to get any kind of info from it. Reformating will not be safe enough. Good luck on your new computer. Go with AMD.

10
Hardware / toshiba portege 7100 series driver...
« on: September 23, 2003, 04:03:53 PM »
This might help also.
http://www.csd.toshiba.com/cgi-bin/tais/su...Model&x=31&y=17

11
Tech Clinic / cmos settings incorrect
« on: September 20, 2003, 07:53:39 AM »
Go ahead on install the memory. If it doesn't work just return it. It the memory you are buying recommended by Gateway ? The psu and other parts are always cheap an Dell's compaq Gateways etc. That is how they can sell a neww P4 for $599.00. Here the old saying . You get what you pay for. Does the computer start in safe mode with the new memory?

12
Tech Clinic / cmos settings incorrect
« on: September 19, 2003, 02:37:38 PM »
You may want to up date the bios on this. How old is it. Gateway does have a 90 watt power supply. They even use it on P4's.

13
Tech Clinic / cmos settings incorrect
« on: September 18, 2003, 06:36:40 PM »
Is the key board working this time. Xp is very funny when you change any hardware. Reinstall the ram them get to your cmos and see if it reads the256. If not you may have bad ram or your computer will only allow you to install the Gateway ram. Look under the support for your computer to see what memory it excepts. Also try removing the 256 and start in safe mode see if it boots. Good luck

14
Hardware / CD ROM drive not responding
« on: September 14, 2003, 10:54:19 AM »
It all depends on what is wrong with the drives. Have you tried them in another computer? Also losing 2 drives means there is a underlaying problem. Also download the right driver for your drive. Normally this doesn't matter. But win me is funny like that.

15
Idle Chat / Computer/Network probs
« on: September 14, 2003, 09:57:25 AM »
Nic maybe or patch cord.

16
Hardware / CD ROM drive not responding
« on: September 14, 2003, 09:55:06 AM »
It could be a short on your mobo. It could happen from Vibration , or a slight jar that you do not know happend. This is just a theory. Is there any other problems you are having?

17
Hardware / CD ROM drive not responding
« on: September 13, 2003, 01:13:50 PM »
Is this drive installed in the computer your other post about the hard drive. If so you could be having problems with the mobo.

18
Tech Clinic / data recovery
« on: September 13, 2003, 01:10:09 PM »
What I would do is. Remave the drive you are using now and install the old one. Change the jumpers, format. Then reload the os. If all is working fine then you can use it. Good luck

19
Hardware / Windows XP networking
« on: September 10, 2003, 04:23:29 PM »
I have 2 xp machines, cable modem, seimans speed steam 2602 router. All the connections are fine. I can access the internet with no problem. I can not setup the computers to see each other. I have tried the the different wizards built in to XP none of them worked. Any help please.

20
Tech Clinic / data recovery
« on: September 10, 2003, 04:13:40 PM »
If your already have a windows os installed on your new h.d. Are you able to hook it up to your other IDE ribbon. If so make sure the jumpers are correct then windows should be able to see the data on the drive.

Pages: [1] 2 3